remove old version of one_pcb_slot (one printed circuit board with space in the back and front)

Octathingy_mount_pcb.scad

@@ -78,69 +78,6 @@ ring_arm_gap = 16;
 
 // the main body that holds the phantom power interfaces
 
-module one_pcb_slot_old (height, pcb_w, pcb_l, pcb_t, pcb_offset, slot_d, front, back, test = false) {
-    d = pcb_t + front + back;
-    render() translate([-(pcb_w/2 + wall/2), -back, 0]) {
-        // make cage with slots for pcb
-        difference() {
-            translate([-2 * wall, 0, 0]) {
-                cube([pcb_w + 4 * wall, d, height]);
-            }
-            translate([slot_d, 0, 0]) {
-                cube([pcb_w - 2 * slot_d, pcb_t + front + back, height]);
-            }
-            translate([0, back, 0]) {
-                cube([pcb_w, pcb_t, height]);
-            }
-            // make top and bottom entry channels
-            translate([slot_d, back + pcb_t/2, 0]) {
-                rotate([0, 0, 45]) cylinder(r1 = pcb_t * 1.1, r2 = 0, h = 8.0, $fn = 4);
-            }
-            translate([pcb_w - slot_d, back + pcb_t/2, 0]) {
-                rotate([0, 0, 45]) cylinder(r1 = pcb_t * 1.1, r2 = 0, h = 8.0, $fn = 4);
-            }
-            translate([slot_d, back + pcb_t/2, height - 8.0]) {
-                rotate([0, 0, 45]) cylinder(r2 = pcb_t * 1.1, r1 = 0, h = 8.0, $fn = 4);
-            }
-            translate([pcb_w - slot_d, back + pcb_t/2, height - 8.0]) {
-                rotate([0, 0, 45]) cylinder(r2 = pcb_t * 1.1, r1 = 0, h = 8.0, $fn = 4);
-            }
-        }
-        // add spar in the back
-        translate([-2 * wall, -back + wall, 0]) {
-            cube([pcb_w + 4 * wall, wall, height]);
-        }
-        // pcb for testing fit
-        if (test) {
-            translate([0, back, pcb_offset]) {
-                cube([pcb_w, pcb_t, pcb_l]);
-            }
-            // small electrolytic capacitors (pcb_version == 2)
-            // https://www.mouser.com/datasheet/2/293/e-umw-1219455.pdf
-            cap_diam = 8.0;
-            // should be 5, but transistors are a bit taller;
-            cap_len = 6.0;
-            translate([pcb_w/2, pcb_t + cap_diam + 0.15, 6]) {
-                rotate([90, 0, 0]) cylinder(r = (cap_diam/2), h = cap_len, $fn = facets);
-            }
-            // film capacitors
-            cap_h = 12;
-            cap_w = 9;
-            cap_t = 5.5;
-            translate([pcb_w/2 - cap_w/2, pcb_t + 0.15, 10]) {
-                cube([cap_w, cap_t, cap_h]);
-            }
-        }
-    }
-    // add capacitor if in test mode
-    *if (test) {
-        cap_diam = 10.2;
-        translate([0, cap_diam/2 + pcb_t, 0]) {
-            cylinder(r = cap_diam/2, h = 20, $fn = facets);
-        }
-    }
-}
-
 // one printed circuit board with space in the back and front
 
 module one_pcb_slot (height, pcb_w, pcb_l, pcb_t, pcb_offset, slot_d, front, back, test = false) {
@@ -166,7 +103,7 @@ module one_pcb_slot (height, pcb_w, pcb_l, pcb_t, pcb_offset, slot_d, front, bac
     }
 }
 
-// the partition that connects inner and outer sections of body
+// the parts that are added to the printed circuit board
 
 module one_pcb_parts (height, pcb_w, pcb_l, pcb_t, pcb_offset, slot_d, front, back) {
     //render() translate([-(pcb_w/2 + wall), -(back + wall), 0]) {