 Fernando Pablo Lopez-Lezcano
|
8a4db5e5c1
calibration: assume all impulse responses have been trimmed and windowed properly, do not try to determine impulse location; many changes in parameters and parameter order; do a running average of filter coefficients when designing the filter transition; determine the transition frequency automatically based on the maximum condition number of the A2B matrices
|
9 anni fa |
|
Fernando Pablo Lopez-Lezcano
|
b1a1dbeb7a
SpHEAR_common: a couple of small changes to the shock mount internal rings
|
9 anni fa |
|
Fernando Pablo Lopez-Lezcano
|
45711bc7b1
calibration: remove dependencies on dates for measured data, replace with 'current' which should be a link to the current set
|
9 anni fa |
|
Fernando Pablo Lopez-Lezcano
|
8b5ac6996d
trim sides of columns at the bottom, make the bridge smaller and cut the connector from the columns to have more space to route wires
|
9 anni fa |
|
Fernando Pablo Lopez-Lezcano
|
cb04cae2e8
h2n: major reorganization of the code, factor blocks into several modules, make everything tilt according to the angle of the support columns, clean up all the major and minor junctures between pieces, almost everything seems to fall into place automatically
|
9 anni fa |
|
Fernando Pablo Lopez-Lezcano
|
6e94c2d6f9
h2n: add parameter to control the fit between the columns and the bridge
|
9 anni fa |
|
Fernando Pablo Lopez-Lezcano
|
750c0b91ec
h2n: cut slots at the bottom of the columns so that we can install the bridge with the wires already threaded into the recorder
|
9 anni fa |
|
Fernando Pablo Lopez-Lezcano
|
304a0be9f6
h2n: bridge now renders correctly with no invisible gaps
|
9 anni fa |
|
Fernando Pablo Lopez-Lezcano
|
3104575ec4
h2n: change orientation of cylinder cutout in columns, this should print better
|
9 anni fa |
|
Fernando Pablo Lopez-Lezcano
|
389b4ed6b4
h2n: change triangular bridge to simple rounded rectangle, modularize most parts, many small changes in shapes - may not be a valid 2-manifold so we need to look at the fit of all parts so they fuse together
|
9 anni fa |
|
Fernando Pablo Lopez-Lezcano
|
d0d9ae83c4
add first try at H2N external capsule array
|
10 anni fa |
|
Fernando Pablo Lopez-Lezcano
|
f6a275ed95
zapnspark: transform molex pin connector pads into smd pads to solder wires directly to the pcb instead of using connectors, should make it slightly easier to assemble the microphone; manually update the component location pdf and svg with new locations
|
10 anni fa |
|
Fernando Pablo Lopez-Lezcano
|
b8eb2f8f92
some tolerance changes for better fit of the parts, fix shock mount eyelet, add hexagonal screw head insert to the stand mount eyelet so that the screw locks properly
|
10 anni fa |
|
Fernando Pablo Lopez-Lezcano
|
89226e2fec
make corners of body more rounded
|
10 anni fa |
|
Fernando Pablo Lopez-Lezcano
|
42bcb85780
zapnspark pcb: move transistors closer together to help fitting the four boards together
|
10 anni fa |
|
Fernando Pablo Lopez-Lezcano
|
102be7d01e
zapnspark pcb: add svg and pdf of component layout from the component side
|
10 anni fa |
|
Fernando Pablo Lopez-Lezcano
|
031b185d4a
zapnspark pcb: move and rotate R3, the end result is much better autorouting of traces and a bigger ground backplane (this change eliminates the weird routing around R1/R2 in the previous version)
|
10 anni fa |
|
Fernando Pablo Lopez-Lezcano
|
88df995d33
re-add side slices of the top of the mount for better cable management, change to proper dimensional parameters so that it works for both 10 and 14mm capsule diameters
|
10 anni fa |
|
Fernando Pablo Lopez-Lezcano
|
5fccdc9de7
shave top of mount slots to get rid of problematic ridge, also add - disabled for now, just testing this - slicing of the top sides of the mount
|
10 anni fa |
|
Fernando Pablo Lopez-Lezcano
|
c746cf4c8c
add better mounting slot in the microphone mount for the four capsule array to fit it, this is much more solid than before although not perfect
|
10 anni fa |
|
Fernando Pablo Lopez-Lezcano
|
3b5d861dd0
changed all pads to be 1.99mm as there were problems with some components lifting the tracks when flexed - for example C2 and C4, hopefully this will fix this issue
|
10 anni fa |
|
Fernando Pablo Lopez-Lezcano
|
1d0e414fbc
zapnspark pcb: a few more tweaks to the component layer
|
10 anni fa |
|
Fernando Pablo Lopez-Lezcano
|
b094d811ab
zapnspark pcb layout: move component names and values to readable places (but printout is still copper side)
|
10 anni fa |
|
Fernando Pablo Lopez-Lezcano
|
bb36093ef1
fix radius of upper capsule array mount to have enough space for the wires
|
10 anni fa |
|
Fernando Pablo Lopez-Lezcano
|
2d4e4f3046
remove redundant transformations from Octathingy mount code
|
10 anni fa |
|
Fernando Pablo Lopez-Lezcano
|
21ae5d7853
Octathingy, add transition to main body to avoid overhang on lower lip
|
10 anni fa |
|
Fernando Pablo Lopez-Lezcano
|
298302b057
in Octathingy remove extra intermediate flare
|
10 anni fa |
|
Fernando Pablo Lopez-Lezcano
|
1681a433e6
in Octathingy also go back to 1mm walls, 2 * that creates trouble printing
|
10 anni fa |
|
Fernando Pablo Lopez-Lezcano
|
604984fbd6
in TinySpHEAR go back to 1mm walls, 2 * that creates trouble printing, the material gets too hot because of the printing pattern and the shape is rough and bumpy, also remove the intermediate flare - we do not really need that for now
|
10 anni fa |
|
Fernando Pablo Lopez-Lezcano
|
4c02aae4e6
tune mount_radius for the Octathingy to hold 8 wires with room to spare (could even be 3.5), fix size of extrusion used to indent the top of the mount
|
10 anni fa |
