SpHEAR/TinySphEAR.scad

//
// TinySphEAR, Tiny Spherical Ear, First Order (B-format) Ambisonics Microphone
//
// Copyright 2015, Fernando Lopez-Lezcano, All Rights Reserved
// nando@ccrma.stanford.edu
//
//
//  This program is free software: you can redistribute it and/or modify
//  it under the terms of the GNU General Public License as published by
//  the Free Software Foundation, either version 3 of the License, or
//  (at your option) any later version.
//
//  This program is distributed in the hope that it will be useful,
//  but WITHOUT ANY WARRANTY; without even the implied warranty of
//  MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
//  GNU General Public License for more details.
//
//  You should have received a copy of the GNU General Public License
//  along with this program.  If not, see <http://www.gnu.org/licenses/>.
//
//
// 3d Models released under the Creative Commons license as follows:
//   Attribution-NonCommercial-ShareAlike 4.0 International (CC BY-NC-SA 4.0)
// http://creativecommons.org/licenses/by-nc-sa/4.0/


// https://en.wikipedia.org/wiki/Tetrahedron
// angle of capsule to vertical axis = atan(sqrt(2)) = 54.7356103172

////
//// model parameters

// dimensions of the EM182 electret microphone
capsule_radius = 5;
capsule_height = 4.5;

// distance between face of capsule and center of array
//
// for a 10mm capsule: with vertical legs -> 10.5mm min radius
//                     with horizontal legs -> 10mm min radius
mic_radius = 10.6;

// dimensions of capsule holder connection legs
// 4mm is too thin for the width, 5mm works better
leg_width = 5;
leg_thick = 3;

// width of the ridge that connects to the mount
ridge_width = 2.0;
ridge_slot_width = 2;

// wall thickness of capsule holder
wall = 1;

// dimensions of microphone holder
mount_radius = 2.75;
mount_wall = 0.75;

// height of mount
mount_height = 30;

// height of sleeve
sleeve_height = 23;
sleeve_wall = 0.75;

// microphone stand mount
//
// diameter of existing shielded wires (x 4)
mic_wire_diam = 1.5;
mic_wire_hole_radius = 2.5;
mic_wire_hole_offset = 5;

// measured diameter = 13.5, inside diameter of sleeve = 13.79 (
mic_mount_radius = 13.50 / 2;
// add this to inside diameter
mic_mount_fit = 0.1;
mic_mount_slot_height = 11.5;
mic_mount_slot_width = 4.25;
mic_mount_slot_radius = 6.25  / 2;
mic_mount_wall = 1.5;
mic_mount_height = 35.0 + mic_wire_hole_offset + mic_wire_hole_radius + 2 * mic_mount_wall;

//// end of model parameters
////
//// rendering control

// what to render:
// 0 -> ready to print
//   set = 0 -> one capsule, set = 1 -> four capsules
// 1 -> the whole microhone with four capsules
rendermic = 1;
renderset = 0;

// what type of connection to use between capsule holders:
// 0 -> original cylindrical angled legs
// 1 -> interlocking horizontal legs
// 2 -> interlocking vertical legs
connect = 2;

// what type of mount ridges to use
// 0 -> nothing
// 1 -> 1 ridge
// 2 -> 2 ridges
ridges = 1;

//// end of rendering control
////

// elevation angle for the capsule holders (fixed for this microphone)
elev_angle = atan(sqrt(1/2));

// angles of the connection legs and adjacent capsule holders
leg_angles_top = 
    [
        [-120, elev_angle], 
        [0, elev_angle],
        [120, elev_angle]
    ];

leg_angles_bot = 
    [
        [-120, elev_angle], 
        [120, elev_angle]
    ];

// adjustment for the inner radius of the capsule holder
//   measured inside diameter of a trial print was around 7.5 to 8.2 
//   instead of 10, capsule diameter was 9.99)
fudge = 0.15;

// adjustment for fit of slots in connection legs and mount
fit = 0.2;

// number of facets for rendering cylinders
facets = 64;

// microphone holder geometry
capsule_sep_min = (mic_radius - capsule_height) * cos(elev_angle) - (capsule_radius + wall) * sin(elev_angle);
capsule_sep_max = mic_radius * cos(elev_angle) - (capsule_radius + wall) * sin(elev_angle);
capsule_bottom = mic_radius * sin(elev_angle) + (capsule_radius + wall) * cos(elev_angle);
mount_radius_capsule = capsule_sep_max;

////////
// microphone capsule holder

// azimuth: horizontal orientation of the capsule
// elevation: vertical orientation of the capsure
// mounts: vectors containing the angle of the mount and the angle to the adjacent capsule
// twist: rotate the whole capsule to match mounting legs
// ridge: 1 -> print ridge for mount
// solid: make the capsule holder solid, used in the mount to carve the capsule rests

module capsule (azimuth, elevation, mounts, twist, ridge, solid = 0) {
	rotate([0, 0, azimuth]) {
		rotate([0, (90 - elevation), 0]) {
  			translate([0, 0, (rendermic == 0 && solid == 0) ? 0 : mic_radius - capsule_height]) {
				difference () {
					union () {
						// main capsule holder
						cylinder(r = capsule_radius + wall, h = capsule_height, $fn = facets);	
						// the mounting legs
						for (angles = mounts) {
							rotate([0, 0, angles[0] + twist]) {
								// connect with cylindrical beams, very pretty
								if (connect == 0) {
                                    leg_length = mic_radius * cos(angles[1]) - capsule_radius * sin(angles[1]);
									translate([capsule_radius - wall, 0, capsule_height - wall]) {
										rotate([0, 180 - angles[1], 0]) {
											cylinder(d = leg_width, h = leg_length - 0.3, center = false, $fn = facets);
										}
									}
								}
								// connect with horizontal legs
								if (connect == 1) {
                                    leg_length = (mic_radius - capsule_height + leg_thick) * tan(90 - angles[1]) - capsule_radius;
                                    slot_depth = leg_thick * cos(90 - 2 * angles[1]) + wall + fit;
									translate([capsule_radius + leg_length + fudge, - leg_width / 3, 0]) {
										rotate([0, -90, 0]) {
											difference() {
												// thickness, width
												cube([leg_thick, leg_width, leg_length]);
												// cut slot in connector
												translate([0, leg_width / 3 - (fit / 2), 0]) {
													cube([leg_thick, leg_width / 3 + fit, slot_depth]);
												}
											}
										}
									}
								}
								// connect with vertical legs
								if (connect == 2) {
                                    // fix this 0.2 == (2 * fudge?)
                                    leg_length = (mic_radius * tan(90 - angles[1]) - capsule_radius) * tan(angles[1]) - 0.2; 
                                    slot_depth = leg_thick * cos (90 - (2 * angles[1]));
									translate([capsule_radius - leg_thick / 2 + fudge, - leg_width / 3, 
                                               - leg_length + capsule_height]) {
										difference() {
											// the connection
                                            difference() {
                                                cube([leg_thick + leg_thick / 2, leg_width, leg_length]);
                                                translate([-leg_thick + wall - fudge, 0, - capsule_height + fudge]) {
                                                    cube([leg_thick, leg_width, leg_length]);
                                                }
                                            }
											// cut slot in connector
											translate([0, leg_width / 3 - (fit / 2), 0]) {
												cube([leg_thick + leg_thick / 2, leg_width / 3 + fit, slot_depth]);
											}
 										}
									}
								}
							}
						}
						// add ridges for microphone mount
                        ridge_length = (mic_radius - capsule_height) / tan(elev_angle) - (capsule_radius + wall);
						if (ridge == 2) {
							rotate([0, 0, twist]) {
								translate([capsule_radius + wall - ridge_length / 2, ridge_slot_width / 2, 0]) {
                                    cube([ridge_length * 3 / 2, ridge_width, capsule_height], center = false);
								}
								translate([capsule_radius + wall - ridge_length / 2, -ridge_width - ridge_slot_width / 2, 0]) {
                                    cube([ridge_length * 3 / 2, ridge_width, capsule_height], center = false);
								}
							}
						}
						if (ridge == 1) {
							rotate([0, 0, twist]) {
								translate([capsule_radius + wall - ridge_length / 2, -ridge_width / 2, 0]) {
                                    cube([ridge_length * 3 / 2, ridge_width, capsule_height], center = false);
								}
							}
						}
					}
					// make the hole for the capsule (also cuts leg overhang for vertical connectors)
					if (solid != 1) {
                        translate ([0, 0, -capsule_height]) {
                            cylinder(r = capsule_radius + fudge, h = capsule_height * 2, $fn = facets);
                        }
                    }
					// remove any extra connecting beam material from the face of the holder
					if (connect == 0) {
						translate ([0, 0, capsule_height]) {
							cylinder(r = capsule_radius + wall * 2, h = 2, $fn = facets);
						}
					}
				}
			}
		}
	}
}

// microphone mount
//
// angles: angles for mount slots
// wall: thickness of cylinder wall
// separation: height of mount with respect of the microphone assembly

module mount (angles, wall, separation, solid = 0) {
    cone_height = 5;
	translate([0, 0, -(separation - 0)]) {
		difference() {
            union() {
                // conic section
                translate([0, 0, -cone_height]) {
                    difference() {
                        cylinder(r2 = mount_radius_capsule, r1 = mount_radius + wall, h = cone_height, $fn = facets);
                        // make the hole for the mount (* 1.5 to cut the ridge as well)
                        if (solid == 0) {
                            cylinder(r2 = mount_radius_capsule - wall, r1 = mount_radius, h = cone_height * 1.5, $fn = facets);
                        }
                    }
                }
                translate([0, 0, -mount_height]) {
                    difference() {
                        cylinder(r = mount_radius + wall, h = mount_height - cone_height, $fn = facets);
                        // make the hole for the mount (* 1.5 to cut the ridge as well)
                        cylinder(r = mount_radius, h = (mount_height - cone_height) * 1.5, $fn = facets);
                    }
                }
            }
            // indentations that match the lower capsule holders
            translate([0, 0, (mic_radius - capsule_height) + capsule_height * sin(elev_angle)]) {
                capsule(angles[0], -elev_angle, [], 0, 1, 1);
                capsule(angles[1], -elev_angle, [], 0, 1, 1);
            }
            // slice it open so we can pop in cables
            if (solid == 0) {
                rotate([0, 0, 45]) {
                    translate([mount_radius - fudge, - mic_wire_diam / 2, -mount_height]) {
                        cube([mount_radius_capsule - mount_radius + fudge, mic_wire_diam, mount_height]);
                    }
                }
            }
        }
    }
}

module mount_sleeve (wall, separation, solid = 0) {
	translate([0, 0, -(separation + 0.0)]) {
		difference() {
            union() {
                // main mount cylinder
                translate([0, 0, -mount_height]) {
                    difference() {
                        cylinder(r = mount_radius + mount_wall + wall, h = sleeve_height, $fn = facets);
                        // make the hole for the mount (* 1.5 to cut the ridge as well)
                        if (solid == 0) {
                            cylinder(r = mount_radius + mount_wall, h = sleeve_height * 1.5, $fn = facets);
                        }
                    }
                }
                // spine that fits into slice of mount body
                rotate([0, 0, 45]) {
                    translate([mount_radius - mount_wall, - mic_wire_diam / 2, -mount_height]) {
                        cube([2 * mount_wall, mic_wire_diam, sleeve_height]);
                    }
                }
            }
            // cut a bit less that one half of the sleeve so it fits around the body
            rotate([0, 0, 45]) {
                translate([-mount_radius - 4 * wall, - (mount_radius + wall) /2, -mount_height]) {
                    cube([mount_radius + wall, (mount_radius + wall), sleeve_height]);
                }
            }
        }
    }
}

// mount for microphone stand
//
module stand_mount (wall, separation) {
	translate([0, 0, -separation]) {
		difference() {
            union() {
                // main mount cylinder
                translate([0, 0, - mic_mount_height]) {
                    difference() {
                        cylinder(r = mic_mount_radius + mic_mount_fit + wall, h = mic_mount_height, $fn = facets);
                        // make the hole for the mount (* 1.5 to cut the ridge as well)
                        cylinder(r = mic_mount_radius + mic_mount_fit, h = mic_mount_height, $fn = facets);
                    }
                }
            }
            // slot for fitting into microphone stand
            translate([mic_mount_radius - wall / 2, - mic_mount_slot_width / 2, - mic_mount_height]) {
                cube([2 * wall, mic_mount_slot_width, mic_mount_slot_height]);
            }
            // eyelet for microphone stand
            translate([mic_mount_radius - wall / 2, 0,  - mic_mount_height + mic_mount_slot_height]) {
                rotate([0, 90, 0]) {
                    cylinder(r = mic_mount_slot_radius, h = 2 * wall, $fn = facets);
                }
            }
            // slot and hole for microphone wiring
            translate([mic_mount_radius - wall / 2, - mic_wire_diam / 2, - mic_wire_hole_offset]) {
                cube([2 * wall, mic_wire_diam, mic_wire_hole_offset]);
            }
            translate([mic_mount_radius - wall / 2, 0, - mic_wire_hole_offset]) {
                rotate([0, 90, 0]) {
                    cylinder(r = mic_wire_hole_radius, h = 2 * wall, $fn = facets);
                }
            }    
        }
    }
}

// the cap that connects the microphone stand mount with the microphone mount

module stand_mount_cap (wall, separation) {
	translate([0, 0, -(separation)]) {
		difference() {
            union() {
                // cap
                cylinder(r = mic_mount_radius + mic_mount_fit + wall, h = wall, $fn = facets);
                translate([0, 0, - 2 * wall]) {
                    cylinder(r = mic_mount_radius + mic_mount_fit, h = 3 * wall, $fn = facets);
                }
            }
            // use mount and sleeve to cut hole of correct size and shape
            translate([0, 0, mount_height - 2 * wall]) {
                mount([45, -135], mount_wall, 0, 1);
                mount_sleeve(sleeve_wall, 0, 1);
            }
            translate([0, 0, - 2 * wall]) {
                cylinder(r = mount_radius + mount_wall, h = 3 * wall, $fn = facets);
            }
            // slot for microphone wiring
            translate([0, - mic_wire_diam / 2, - 2 * wall]) {
                cube([mic_mount_radius + mic_mount_fit + wall, mic_wire_diam, 3 * wall]);
            }
        }
    }
}


// render a complete microphone

if (rendermic == 1) {
	capsule(45, elev_angle, leg_angles_top, 60, 0);
	capsule(-135, elev_angle, leg_angles_top, 60, 0);
	capsule(-45, -elev_angle, leg_angles_bot, 0, 1);
    capsule(135, -elev_angle, leg_angles_bot, 0, 1);
	// the mount
	mount([-45, 135], mount_wall, capsule_bottom);
    // the sleeve closing it
    mount_sleeve(sleeve_wall, capsule_bottom);
    // the microphone stand mount
    stand_mount_cap(mic_mount_wall, capsule_bottom + mount_height + 3);
    stand_mount(mic_mount_wall, capsule_bottom + mount_height + 7);
}

// print all the parts separately

if (rendermic == 0) {
    if (connect == 1) {
        part_rot = 90;
        part_height = 0;
        part_sep = capsule_radius * 2.5;
        // #3
        translate([part_sep, -part_sep, part_height]) { capsule(0, part_rot, leg_angles_top, 60, 0); }
        if (renderset != 0) {
            // #4
            translate([part_sep, part_sep, part_height]) { capsule(0, part_rot, leg_angles_top, 60, 0); }
            // #2
            translate([-part_sep, part_sep, part_height]) { capsule(0, part_rot, leg_angles_bot, -90, 1); }
            // #1
            translate([-part_sep, -part_sep, part_height]) { capsule(0, part_rot, leg_angles_bot, 90, 1); }
            // mount body
            translate([0, 0, mount_height]) { mount([-45, 135], 1, 0); }
            // mount sleeve
            translate([mount_radius * 8, 0, mount_height]) { mount_sleeve(1, 0); }
            // add connecting ridges to make it all one part
            difference() {
                for (rot_a = [-45, 45]) {
                    rotate([0, 0, rot_a]) {
                        translate([-wall / 2, -part_sep, 0]) {
                            cube([wall, part_sep * 2, wall / 2]);
                        }
                    }
                }
                // remove them in the inside of the mount
                cylinder(r = mount_radius + wall / 2, h = wall / 2);
            }
        }
    } else {
        // connect == 2
        part_rot = -90;
        part_height = capsule_height;
        part_sep = capsule_radius * 2;
        // #3
        translate([part_sep, -part_sep, part_height]) { capsule(0, part_rot, leg_angles_top, 0, 0); }
        if (renderset != 0) {
            // #4
            *translate([part_sep, part_sep, part_height]) { capsule(0, part_rot, leg_angles_top, 0, 0); }
            // #2
            translate([-part_sep, part_sep, part_height]) { capsule(0, part_rot, leg_angles_bot, -90, 1); }
            // #1
            translate([-part_sep, -part_sep, part_height]) { capsule(0, part_rot, leg_angles_bot, 90, 1); }
            // mount
            *rotate([0, 0, 45]) {
                translate([0, 0, mount_height]) { mount([-45, 135], mount_wall, 0); }
            }
            // mount sleeve
            *translate([10, 0, mount_height]) {
                rotate([0, 0, 45]) {
                    mount_sleeve(sleeve_wall, 0); }
            }
            // stand mount
            *translate([0, 0, mic_mount_height + mic_mount_height]) {
                stand_mount(mic_mount_wall, mic_mount_height);
            }
            // stand mount cap
            *rotate([0, 180, 0]) {
                translate([2 * mic_mount_radius + 8, 0, - mic_mount_wall]) {
                   stand_mount_cap(mic_mount_wall, 0);
                }
            }
            // add connecting ridges to make it all one part
            *difference() {
                for (rot_a = [-45, 45]) {
                    rotate([0, 0, rot_a]) {
                        translate([-wall / 2, -part_sep * 0.85, 0]) {
                            cube([wall, part_sep * 1.75, wall / 2]);
                        }
                    }
                }
                // remove them in the inside of the mount
                cylinder(r = mount_radius + wall / 2, h = wall / 2);
            }
        }
    }
}