#pragma once

// Board- and application-wide configuration.
//
// Wi-Fi credentials, the outdoor sensor URL, the timezone and the NTP server
// are runtime settings held in NVS and entered through the setup portal — see
// src/settings.h and src/portal.h. The values below are compile-time
// constants and safe to commit.

// ---------------------------------------------------------------- display ---
// The panel is a 300 x 400 ST7305 reflective LCD. The application runs it
// rotated (U8G2_R1), so the drawing surface is 400 wide by 300 high.
#define LCD_NATIVE_WIDTH   300
#define LCD_NATIVE_HEIGHT  400
#define DISPLAY_WIDTH      400
#define DISPLAY_HEIGHT     300

#define RLCD_SCK_PIN       11
#define RLCD_MOSI_PIN      12
#define RLCD_DC_PIN        5
#define RLCD_CS_PIN        40
#define RLCD_RST_PIN       41
#define RLCD_TE_PIN        6   // tearing effect output, unused

// Layout: top 60% is time + date, bottom 40% is indoor | outdoor.
#define LAYOUT_SPLIT_Y     180
#define LAYOUT_MID_X       200

// ------------------------------------------------------------------- i2c ---
#define I2C_SDA_PIN        13
#define I2C_SCL_PIN        14
#define I2C_FREQ_HZ        400000

#define PCF85063_ADDR      0x51
#define SHTC3_ADDR         0x70

// BH1750 ambient light sensor, wired to the same bus on the expansion header.
// Optional: without it the display falls back to quiet hours from the clock.
// The part answers on 0x23 with ADDR low and 0x5C with ADDR high; both are
// probed at boot.
#define BH1750_ADDR_LOW    0x23
#define BH1750_ADDR_HIGH   0x5C

// --------------------------------------------------------------- battery ---
// 18650 voltage divider, per the vendor's 03_ADC_Test: ADC1 channel 3 with a
// 1:3 divider, so the measured millivolts are multiplied by three.
#define BATTERY_ADC_PIN    4
#define BATTERY_DIVIDER    3.0f
#define BATTERY_SAMPLES    16      // oversampling per reading
#define BATTERY_READ_MS    60000UL

// --------------------------------------------------------------- buttons ---
// Both onboard buttons are active low. KEY is the application button; BOOT is
// avoided because holding it at reset also enters the ROM download mode.
#define KEY_BUTTON_PIN     18
#define BOOT_BUTTON_PIN    0

// Hold KEY for this long during power-up to force the setup portal.
#define KEY_FORCE_SETUP_MS 1500

// ------------------------------------------------------------------ time ---
// Defaults for a freshly erased device; both are editable in the setup portal.
#define NTP_SERVER_1       "pool.ntp.org"
#define NTP_SERVER_2       "time.google.com"

// POSIX TZ string for Australia/Hobart (AEST-10, AEDT from Oct to Apr).
#define TIMEZONE_POSIX     "AEST-10AEDT,M10.1.0,M4.1.0/3"

// Clock and date presentation defaults; all three are editable in the setup
// portal. DATE_FORMAT is a strftime(3) string — "%A %e %B" is "MONDAY 24
// AUGUST".
#define CLOCK_24H_DEFAULT      true
#define DATE_FORMAT            "%A %e %B"
#define DATE_UPPERCASE_DEFAULT true

// ----------------------------------------------------------------- setup ---
// Soft-AP the device raises when it has nothing to connect to. The password
// must be at least 8 characters or the AP comes up open.
#define SETUP_AP_SSID      "TempDisplay-Setup"
#define SETUP_AP_PASSWORD  "temp1234"
#define DEVICE_HOSTNAME    "temp-display"

// ------------------------------------------------------------ power save ---
// 80 MHz is the lowest the ESP32-S3 can run with Wi-Fi active and leaves the
// 80 MHz APB clock — and so the display SPI — untouched.
#define CPU_FREQ_MHZ       80

// Defaults for the power-saving settings, all editable in the setup portal.
#define SHOW_BATTERY_DEFAULT      true
#define SLEEP_WHEN_DARK_DEFAULT   true
#define PANEL_LOW_POWER_DEFAULT   true
#define DARK_LUX_DEFAULT          5     // below this the room is unreadable
#define QUIET_START_HOUR_DEFAULT  23    // used only when no sensor is fitted
#define QUIET_END_HOUR_DEFAULT    6

// Hysteresis, so a flickering or marginal reading cannot chatter the display
// in and out of sleep. Waking needs a clearly brighter room than sleeping.
#define DARK_LUX_HYSTERESIS       3.0f

// While asleep in a dark room, wake this often to re-check the light level.
// Short enough that the clock is at most one minute stale when the lights come
// on, long enough that the duty cycle is well under 1%.
#define DARK_RECHECK_MS    20000UL

// -------------------------------------------------------------- intervals ---
#define WIFI_CONNECT_TIMEOUT_MS   20000UL   // give up on a connect attempt
#define WIFI_RETRY_MS             60000UL   // then retry this often
#define NTP_RESYNC_MS             (6UL * 60UL * 60UL * 1000UL)
#define INDOOR_READ_MS            30000UL
#define OUTDOOR_POLL_MS           30000UL
#define OUTDOOR_STALE_MS          (10UL * 60UL * 1000UL)  // mark reading stale
#define DISPLAY_TICK_MS           1000UL    // check-for-change rate

// ---------------------------------------------------------------- outdoor ---
// HTTP timeout for one outdoor poll.
#define OUTDOOR_HTTP_TIMEOUT_MS   5000

// Plausible temperature range; readings outside it are rejected.
#define TEMP_MIN_VALID     -50.0f
#define TEMP_MAX_VALID     80.0f

// Optional development conveniences. include/secrets.h is gitignored; when it
// exists its values seed a freshly erased device so a bench unit does not need
// to be re-provisioned through the portal after every flash erase.
#if __has_include("secrets.h")
#include "secrets.h"
#endif